Plane crash map Locate crash sites, wreckage and more

N28VS accident description

California map... California list
Crash location 33.258889°N, 116.320834°W
Nearest city Borrego Springs, CA
33.255872°N, 116.375012°W
3.1 miles away
Tail number N28VS
Accident date 08 Apr 2010
Aircraft type Snow Rocket F1
Additional details: None

NTSB Factual Report

HISTORY OF FLIGHT

On April 8, 2010, about 1258 Pacific daylight time, an experimental amateur built Snow Rocket F1, N28VS, was substantially damaged when it impacted terrain while maneuvering near Borrego Springs, California. The airplane was registered to and operated by the pilot under the provisions of Title 14 Code of Federal Regulations Part 91. The private pilot, sole occupant of the airplane, was killed. Visual meteorological conditions prevailed and no flight plan was filed for the personal flight. The local flight originated from the Borrego Valley Airport (L08), Borrego Springs, about 1250.

Information provided by the International Aerobatic Club (IAC) Chapter 36, revealed that the pilot was scheduled to participate in the annual Borrego Hammerhead Roundup aerobatic competition. The IAC Chapter 36 representative stated that prior to event registration, pilot's were allotted a 10-minute practice session in the designated aerobatic area.

A witness located on the ramp of L08 reported that while working the aerobatic box, she first established radio contact with the pilot while he was in the primary holding area southeast of the airport. The pilot proceeded to fly into the designated aerobatic box and perform a sportsman sequence twice while receiving coaching from a person on the ground. He then performed a spin maneuver, which was followed by his departure of the aerobatic box to the north. The witness recalled that the pilot was requested to repeat the "goldfish figure" at which point she informed the pilot he had two minutes left on his allotted practice time. The pilot transmitted that he was going to reenter the aerobatic box from the west while traveling east. The witness informed the pilot to take his time, as he had plenty of time left within the aerobatic box and the pilot acknowledged.

The witness estimated that the airplane was at an altitude of between 2,700 and 3,000 feet above ground level (agl) when the pilot made a right turn to enter the aerobatic box. The witness said the airplane entered a 30-35 degree descent in order to obtain "speed/energy" to begin his maneuvers. Shortly after, the pilot transmitted in the blind "I have no back stick." The witness estimated that the airplane was descending through about 1,800 to 2,000 feet agl when the witness heard someone ask the pilot if the airplane was under control. The pilot responded "no, not at all." A few seconds later, the witness heard another transmission telling the pilot to "try your trim." The pilot responded "there is no trim" as the airplane was observed descending through about 600 feet agl. No further radio transmissions were heard from the pilot. The witness further reported that the airplane continued to steepen its descent angle and gain airspeed prior to losing sight of it behind a sand dune.

Examination of the airplane by a Federal Aviation Administration (FAA) inspector revealed that the wreckage came to rest inverted in the open desert about one mile north east of L08. All major structural components of the airplane were located at the accident site. The fuselage was crushed aft and the engine was separated from the fuselage. The left and right wings remained attached to the fuselage and were crushed aft to the main spar throughout their respective spans. The wreckage was recovered to a secure location for further examination.

PERSONNEL INFORMATION

The pilot, age 58, held a private pilot certificate with an airplane single-engine land and instrument airplane ratings. An FAA third-class airman medical certificate was issued on March 10, 2010, with no limitations stated. The pilot reported on his most recent medical certificate application; that he had accumulated 2,100 total flight hours. Review of the pilot's personal logbook revealed that as of the most recent logbook entry dated April 4, 2010, the pilot had accumulated a total amount of flight time of 1,268.7 hours, of which 10.2 were within the preceding 30 days and 19.3 hours within the preceding 90 days of the accident.

AIRCRAFT INFORMATION

The two-seat, low-wing, fixed-gear airplane, serial number (S/N) 001, was built in 2008. It was powered by a Lycoming IO-540-EXP engine, serial number L-51474-04, rated at 340 horse power. The airplane was also equipped with a Whirlwind three-bladed adjustable pitch propeller. The airplane had two sets of controls, consisting of front and rear control sticks and two sets of rudder pedals. The two control sticks were interconnected via a torque tube assembly.

Review of the aircraft maintenance logbooks revealed that the most recent 100-hour inspection performed on the airplane was completed on December 18, 2009, at a tachometer time and airframe total time of 191.4 hours.

MEDICAL AND PATHOLOGICAL INFORMATION

The County of San Diego Medical Examiner conducted an autopsy on the pilot on April 9, 2010. The medical examiner determined that the cause of death was "multiple blunt force injuries."

The FAA's Civil Aeromedical Institute (CAMI) in Oklahoma City, Oklahoma, performed toxicology tests on the pilot. According to CAMI's report, volatiles, and drugs were tested with negative results.

TESTS AND RESEARCH

The wreckage was examined at the facilities of Aircraft Recovery Services, Pear Blossom, California, on April 28, 2010, by the National Transportation Safety Board investigator-in-charge. The examination of the airframe revealed that the elevator flight control system exhibited numerous areas of separations from the rear control stick to the elevator control surface. All areas of separations exhibited signatures consistent with overload. The front and rear control sticks were found separated from their control columns. The interconnected control column, portions of the separated front and rear control sticks, elevator control servo, and a portion of control rod were removed from the wreckage and subsequently sent to the NTSB Materials Laboratory, Washington, D.C. for further examination. The upper portion of the front control stick was not located.

An NTSB senior metallurgist reported that all fractures associated with these components were inspected using a 5X to 50X stereo zoom microscope. All fracture surfaces on the control column; and both flight control sticks were found to be due to overstress. The front control stick had a 0.22 inch diameter hole drilled in the forward side of the tube wall about 0.42 inch above the top of the stick socket. The overstress fracture initiated at the edges of this hole. The rear control stick had a 0.15 inch diameter hole drilled in the forward and aft sides of the tube wall (clearance holes to accommodate a mounting bolt) about 0.40 inch below the top of the stick socket. The overstress facture in the rear stick initiated at the edges of the forward hole.

The linkage fractures associated with the elevator control servo assembly were inspected using a 5X to 50X stereo zoom microscope. In all instances, the fractures were found to be consistent with a bending overstress. A control linkage that measured approximately 18 inches long and 0.5 inch in diameter had threaded ends. Both of the threaded end's fracture surfaces were consistent with bending overstress as indicated by inspection.

Examination of the front control stick revealed that it was fractured in overstress due to cantilever bending just above the control column fitting. Near the top of the front control stick, six 4-40 NC threaded holes were located within the tube. The threads appeared to be stripped within holes labeled one, four, and six. Hole number four exhibited a second untapped hole overlapping it. The top of the front control stick appeared to be saw-cut and hand filed.

According to a representative from Team Rocket LP, the control sticks were fabricated from aluminum alloy 6061 and tempered to the T6 condition. Examination of the front and rear control sticks revealed that the aluminum alloy composition and tube wall thickness were within specification limits. The hardness and conductivity measurements for both control sticks were found consistent with aluminum alloy 6061 in a T4 or a lower strength T6 condition.

NTSB Probable Cause

The pilot's inability to maintain control due to the in-flight failure and separation of the pilot's flight control stick. The reason for the flight control stick failure could not be determined.

© 2009-2020 Lee C. Baker / Crosswind Software, LLC. For informational purposes only.