Plane crash map Locate crash sites, wreckage and more

N88452 accident description

Alaska map... Alaska list
Crash location 64.541944°N, 147.757778°W
Reported location is a long distance from the NTSB's reported nearest city. This often means that the location has a typo, or is incorrect.
Nearest city Fairbanks, AK
64.837778°N, 147.716389°W
20.5 miles away
Tail number N88452
Accident date 07 Dec 2016
Aircraft type Bellanca 7GCBC
Additional details: None

NTSB Factual Report

On December 7, 2016, about 1043 Alaska standard time, a tailwheel, ski-equipped Bellanca Citabria 7GCBC airplane, N88452, was substantially damaged when it impacted terrain about 17 miles southeast of Fairbanks, Alaska. The airline transport pilot was fatally injured. The airplane was registered to and operated by the pilot as a Title 14 Code of Federal Regulations Part 91 visual flight rules (VFR) personal flight. Visual meteorological conditions prevailed at the time of the accident, and a VFR flight plan was filed and activated. The local area flight departed Chena Marina Airport (AK28), Fairbanks, at 1026.

According to the Federal Aviation Administration (FAA) Fairbanks Flight Service Station records, the pilot filed a local flight plan for a 3-hour flight within a 50-mile area to the east, south and west of Fairbanks International Airport (FAI). The mechanic who had recently worked on the airplane stated that the purpose of the flight was to test the airplane's flight performance following the installation of vortex generators (VGs) on the wings and horizontal stabilizer. The airplane's engine ran rough after the first start, so the mechanic brought the airplane back into the hangar to warm up. He checked the fuel sumps for debris and found none. After warming, the airplane was pushed outside and operated normally after the second start.

A review of archived FAA radio communication recordings revealed that the pilot called the FAI air traffic control tower before departure and was provided the current wind of 350° at 5 knots and the altimeter setting of 30.64 inches of mercury. After departure, he requested that his VFR flight plan be activated. The last transmission from the pilot was at 1033 when he asked the FAI tower if the restricted airspace R-2211 was "hot"; the tower reported it was "cold."

A Garmin GPSMAP 296 portable GPS receiver was recovered from the wreckage and downloaded at the National Transportation Safety Board (NTSB) Vehicle Recorder Laboratory. The recorded data included time, location, and GPS altitude, as well as derived groundspeed and track information.

The airplane began its takeoff roll at Chena Marina Airport at 1026:14, climbed toward the southeast to a GPS altitude of 1,762 ft, and proceeded south over the Tanana Flats. Between 1033:11 and 1037:07, the airplane performed one right 360° turn and two 420° turns (one to the left and one to the right) while flying between GPS altitudes of 1,601 ft and 1,437 ft and maintaining groundspeeds of 44 to 100 knots.

At 1037:07, the airplane turned to a southwesterly track of 194° to 201° for about 3 minutes and performed slow flight maneuvers. During this period, the airplane slowed to 46 knots for a period of 19 seconds, accelerated, and then slowed to 40 knots for 14 seconds before accelerating to 68 knots; these changes in airspeed were consistent with the pilot practicing stalls.

At 1040:52, the airplane began a southeast track of 133° that lasted for 2 minutes 36 seconds. During this final track, the airplane descended from 1,545 ft to 981 ft, decelerated from 81 knots to 26 knots, and then entered a rapid descent at a rate of about 2,000 ft per minute (fpm) and a rapid turn to the south. About 30 seconds before the rapid descent began, the airplane had a rate of descent of 510 fpm as it decelerated below 40 knots. The last valid GPS data point indicated an increasing groundspeed of 35 knots, an altitude of 587 ft (75 ft above ground level), and a track of 144°.

According to FAA air traffic control recordings and documentation, at 1318, about 2.5 hours after the last GPS data point, two US Army CH-47F helicopter crews were flying through the area and located the airplane wreckage after hearing an emergency locator transmitter signal.

PERSONNEL INFORMATION

The pilot, age 74, held an airline transport pilot certificate with an airplane multi-engine land rating. Additionally, he held commercial privileges for airplane single-engine land and single-engine sea. He held a third-class medical certificate issued on January 22, 2016, with the limitation: must have available glasses for near vision. According to documentation provided by family members, the pilot was well rested and in good health the morning of the accident.

The pilot co-owned the airplane with his son. The pilot also owned a Cessna 180 and had been flying it at least monthly according to his logbook entries.

Examination of the pilot's logbook revealed that he had recorded about 3,171 hours of flight experience, of which 2,736 hours were in single-engine airplanes and 206 hours were in a Citabria 7GCBC. The pilot's most recent flight review was conducted on February 24, 2016, in his Cessna 180 airplane. The flight instructor who conducted the last flight review stated that he was not sure if stalls were performed during the most recent flight review, but he recalled performing stalls during other reviews with the pilot. He also stated that the pilot was a very competent and conservative pilot.

AIRCRAFT INFORMATION

The two-seat, high-wing, conventional-gear airplane was manufactured in 1974 and equipped with a 150-horsepower Lycoming O-320-A2D reciprocating engine and a fixed-pitch, two-bladed McCauley metal propeller. The airplane had been altered by the installation of metal wing spars in accordance with FAA Supplemental Type Certificate (STC) SA3829NM. During the week before the accident, the airplane was equipped with Landis L-2000A straight skis in accordance with FAA STC SA261AL and Micro Aerodynamics vortex generators in accordance with FAA STC SA00795SE. The optional stall warning horn was not installed.

A review of the maintenance logbooks revealed that the last annual inspection of the airplane was completed on April 4, 2016, at which time the airframe and engine total times were 2,882.24 hours, and the engine time since major overhaul was 875.24 hours. According to the mechanic who maintained the airplane and the logbook entries, the engine throttle cable was removed and replaced the week before the accident due to a stiff throttle. The alternator was removed and replaced the day before the accident due to electrical issues that the airplane had on December 2. The transponder was removed for maintenance before the flight. At the time of the accident, the tachometer indicated 2,889.34 hours and the recording hour meter indicated 1,229.0 hours.

Weight and Balance

The actual gross weight of the airplane at the time of the accident could not be determined as the fuel quantity could not be verified. According to the mechanic's recollection, the fuel tanks were about 3/4 full before engine start, which would have been about 27 gallons. The airplane's weight and balance condition at the time of takeoff was calculated based on the estimated fuel onboard (156 lbs), the estimated pilot weight based on his most recent medical application and winter clothing (215 lbs + 4 lbs), actual cargo weights (1 lb front seat + 2.5 lb rear seat + 94 lbs in rear baggage area), and the airplane weight and balance form for the Landis ski configuration (1218 lbs empty weight + 15 lbs oil).

Page 1-3 of the Bellanca Citabria Pilot Operation Manual (POM) lists the maximum allowable gross weight of 1,650 lbs and the center of gravity limits between 14.2 inches and 19.2 inches aft of datum. The calculated takeoff weight was 1,705 lbs, which was 55 lbs above the maximum allowable gross weight. The airplane's weight at the time of the accident, about 18 minutes later with an estimated 24 gallons of fuel remaining, was calculated at 1,687 lbs. The center of gravity at the time of the accident was calculated using figures 5-1, 5-2 and 5-5 from the Citabria POM and determined to be 17.18 inches.

METEOROLOGICAL INFORMATION

The closest weather reporting facility to the accident site was at FAI, which was located about 16 miles north of the accident site at an elevation of 432 ft. At 1053, the recorded weather at FAI was wind from 010° at 5 knots, visibility 10 miles, sky clear below 12,000 ft, temperature -33°C, dew point temperature -36°C, and altimeter setting 30.63 inches of mercury.

On the day of the accident, sunrise in Fairbanks was at 1037. According to the National Oceanographic and Atmospheric Administration solar calculator, the sun was at an elevation angle of 0.1° above the horizon at an azimuth of 153° true at 1043.

On December 9, 2016, the NTSB investigator-in-charge (IIC) noted that while flying to the accident site via helicopter about 1100, sun glare was present in the direction of the rising sun, which made viewing the terrain details difficult.

For further weather information, see the weather study located in the public docket for this accident.

WRECKAGE AND IMPACT INFORMATION

The wreckage was located within the southern border of the Fort Wainwright US Army base, about 7 miles south of Clear Creek Butte, in an open level area of snow-covered tundra and small groves of black spruce trees. All major components of the airplane were located at the accident site, which was contained within an area about 60 ft long and 20 ft wide at an elevation of about 512 ft. The airplane came to rest intact with the fuselage resting on the ground in a right 30° bank, in a slightly nose-down attitude, and on a heading of 220°. The initial impact point was indicated by three freshly fractured spruce tree tops about 350 ft northwest of the wreckage. The tallest tree was estimated to be 55 ft high. Red and white paint chips matching the airplane were located on the ground among broken limbs as thick as 4 inches in diameter. Initial ground impact was evident at two parallel ski marks in the snow and grass on a bearing of 140° from the damaged spruce trees. The tracks were about 30 ft long and were followed by about another 30 ft of disturbed snow patterns northwest of the wreckage.

The right wing sustained significant fore to aft crush damage to the inboard 8 ft of the wing structure with numerous main and rear spar fractures. An elliptical compression in the wing leading edge was about 1.5 ft deep and 6 inches wide, and tree bark and spruce needles were present in the damaged area. The wing was twisted upward and rotated rearward about 75° from the lateral axis. The right flap and aileron remained attached, and the flap was crushed. The left wing separated from the airframe at the lower lift strut bracket and folded up inverted over the top of the fuselage and came to rest with the wing root intruding downward into the cabin space. The left aileron and flap remained intact and attached. The fuel tanks were ruptured; however, fuel was present in the left wing, and samples were consistent with clear, bright, 100LL aviation gasoline.

The empennage remained attached to the fuselage with crush damage evident to the right horizontal stabilizer leading edge and a partially detached and torn right elevator. The outer portion of the right elevator was separated at a fracture in the torque tube and located at the initial ground impact point. The vertical stabilizer, rudder, and left horizontal stabilizer and elevator sustained minimal damage. Two of the rear fuselage wooden bulkheads sustained fractures and exhibited dark gray areas that indicated the presence of previous water damage.

Control continuity in the elevator, rudder, and ailerons was established from the cockpit to the control surfaces. The left flap control system was fractured at the torque tube at the wing root and the control rod. The right flap system was continuous out to the damaged wing section. The mechanical flap handle was secure in the full up notch, which was the flaps full down position.

The right forward fuselage exhibited downward crush damage which included buckled and separated right door and sidewall structure. The left fuselage upright support frames were separated and bent right which exposed the top front cabin area. The front windscreen, supports, and all glass were fragmented and scattered throughout the wreckage field. The throttle and propeller controls were full forward, and the mixture was out slightly. The carburetor heat lever was slightly aft of full forward. The electrical master switch was off, and the magneto switch was in the both position. The fuel valve handle was down. The elevator trim control was 2/3 forward. The altimeter indicated 620 ft with a Kollsman window setting of 30.68, and the vertical speed indicator had an indication of 175 fpm. The accelerometer indicated -2, 2, and a maximum load factor of 12 Gs.

The pilot's lap belt was latched around the pilot and attached to the seat frame, which was partially attached to the cabin floor. The pilot's shoulder harness was disconnected from the lap belt, and the inertial reel and harness remained attached to the cabin overhead tubing, which was torn away from the main structure. A detailed examination of the pilot's seat revealed that the left forward and aft support legs were separated from the airframe mounting structure, which had been altered with the addition of 15-inch-long thin metal brackets at each side that allowed for the fixed pilot seat to be installed further aft on the floor.

The right landing ski was located about 30 ft northwest of the wreckage with springs and cable attached. The landing gear leg was fractured at the airframe mount, and the ski exhibited a transverse fracture at the midspan. The left landing ski and the tail wheel and ski remained attached to the airframe with cables and springs intact.

The Micro VGs on the wings and horizontal stabilizer were examined, measured, and determined to be installed in accordance with the Micro Vortex Generator Kit Installation Manual MA2132 rev B. Some VGs were absent in areas of impact damage.

The engine remained attached to the airframe and exhibited impact damage to the right lower side. Examination of the engine revealed no evidence of anomalies, contamination, or malfunctions in any of the engine accessories. The cylinders, pistons, valve train, crankshaft, and other internal components showed no evidence of anomalies or malfunctions that would have precluded normal operation. Control continuity from the cockpit to the engine was established. Throttle cable binding was observed where an airframe mount had fractured at the weld due to impact forces. The fuel lines from the wing roots to the gascolator were clear of debris.

The propeller remained attached to the crankshaft, and one propeller blade exhibited a complete fracture through the mid-section about 1.6 ft from the blade butt. The fractured propeller tip was not located. The other propeller blade exhibited a span-wise torsional twist with a trailing edge "S" bending signature, indicative of rotational force during impact.

A senior metallurgist at the NTSB Materials Laboratory conducted examinations of the left-wing strut fracture and the throttle cable fuselage mount fracture. Magnified examinations of the throttle cable mounting bracket revealed fracture features and overall deformation patterns consistent with a twisting overstress fracture and separation after significant displacement of the bracket and no evidence of preexisting cracking or corrosion. The fractured left lift strut attachment was separated near the attaching bolt hole and displayed features and deformation patterns indicating a bending overstress separation with no corrosion or preexisting cracking noted.

MEDICAL AND PATHOLOGICAL INFORMATION

The Alaska State Medical Examiner, Anchorage, Alaska, performed an autopsy of the pilot. The report attributed the pilot's cause of death to multiple blunt force injuries.

The FAA Bioaeronautical Sciences Research Laboratory, Oklahoma City, Oklahoma, performed forensic toxicology on specimens from the pilot with negative results for carbon monoxide, cyanide, ethanol, and listed drugs.

ADDITIONAL INFORMATION

Air Traffic Control

An NTSB air traffic control specialist reviewed recorded Fairbanks radar data for the time and location of the accident flight but found no associated primary or mode C targets. The specialist reported that radar coverage in the accident area is limited due to terrain interference.

According to a statement and memoran

NTSB Probable Cause

The pilot's operation of the airplane at an altitude that was too low to allow for recovery from an intentional aerodynamic stall, which resulted in an impact with terrain. Contributing to the accident were the pilot's inability to recognize altitude deviations during slow flight due to the sun glare and the pilot's lack of knowledge of the stall performance characteristics of the airplane modified with vortex generators due to the lack of information from the manufacturer.

© 2009-2020 Lee C. Baker / Crosswind Software, LLC. For informational purposes only.