NTSB Factual Report

HISTORY OF FLIGHT

On January 22, 2000, at 1432 central standard time, a Mitsubishi MU-2B-26A twin-engine airplane, N386TM, was destroyed when it collided with terrain following a loss of control during the initial takeoff climb from the San Antonio International Airport, San Antonio, Texas. The airplane was registered to and operated by BTC Saratoga Inc., of Saratoga, California. The two occupants, a private pilot and a commercial pilot, sustained fatal injuries. Visual meteorological conditions prevailed, and an instrument flight rules (IFR) flight plan was filed for the 14 Code of Federal Regulations Part 91 personal flight. The cross-country flight was originating at the time of the accident and was destined for the San Jose International Airport, San Jose, California, with an intermediate fuel stop at the Tucson International Airport, Tucson, Arizona.

According to the San Angelo Flight Service Station, at 1338, the commercial pilot of N386TM received a standard weather briefing and filed two IFR flight plans. The first flight plan was for a flight from San Antonio to Tucson and the second was for a flight from Tucson to San Jose.

Line service employees reported that the airplane's fuel tanks were topped off before the airplane departed from the San Antonio International Airport. One employee stated that he observed the right engine start first. The right engine operated for 10 minutes, and then the left engine was started. He then observed the airplane taxi toward the departure area of the ramp and stop. With both engines operating, he observed a person exit the airplane, "check [the] nose gear," and re-board. The airplane then taxied to the runway.

According to air traffic control (ATC) transcripts, at 1411, N386TM requested and received an IFR clearance to Tucson. At 1419, N386TM contacted San Antonio ground control and stated that the airplane was ready to taxi, and the controller instructed the flight to taxi to runway 30L (8,502 feet long). At 1420, N386TM advised the ground controller that the flight had a "minor delay," and that they would be stopped on the ramp for a couple of minutes; subsequently, at 1423, N386TM stated they were moving again. At 1430, N386TM contacted the tower controller and advised that the flight was ready for takeoff and, subsequently, the flight was cleared for takeoff. At 1431, the tower controller advised N386TM of an MD-80 on a 3.5 mile final and requested that the airplane depart with no delay. N386TM acknowledged. No further communications, or distress calls, were received from N386TM.

According to witnesses located on airport property, they observed the airplane initiate the takeoff roll and become airborne. Two witnesses reported that during the takeoff roll they heard a series of repeated sounds, which they described as similar to a "backfire" or "compressor stall." One of the two witnesses stated that as the airplane was climbing out and had reached the departure end of the runway, "the right propeller quit." The second witness reported the following events; as the airplane lifted off the ground, he heard "a loud cracking sound followed by an immediate prop wind down into feather." The gear was retracted and the airplane entered a climb and right turn. The airplane then entered a left bank and started a descent. Subsequently, the airplane pitched up, entered a "Vmc roll-over," followed by a 360-degree turn, and impacted the ground.

Two additional witnesses, who were also on airport property, observed the airplane after it became airborne. One witness stated that he observed the right engine's propeller stop turning during the climb. He added that the airplane entered a right bank and he then saw the right propeller turn, "like it wanted to start," and then the propeller stopped again. The other witness stated that "the right engine was slowly shutting down," and added that he saw a "puff of smoke come out of the right engine;" however he did not see any fire.

According to a witness, who was in a vehicle and stopped at a traffic light, he observed "a small plane with two propellers, but only one was working." He stated that the right propeller was not turning and he did not see any smoke.

Radar data provided by the FAA depicted the airplane beginning its takeoff roll between 1431:25 and 1431:30. At 1432:02, the airplane's Mode C altitude changed from 800 to 900 feet msl. At 1432:11, the airplane's Mode C altitude changed from 900 to 1,000 feet msl (approximately 200 feet agl) and remained there until it decreased to 900 feet msl at 1432:30, when the last radar return was recorded. Between 1432:11 and 1432:30, the airplane turned right from runway heading to a north heading. According to a radar study provided by Mitsubishi, the airplane became airborne after a ground roll of approximately 3,000 feet at a calibrated airspeed of 89 knots. The airplane's calibrated airspeed continued to increase until it reached a maximum of 132 knots at 1432:07, and then it began to decrease reaching 97 knots at 1432:30.

PERSONNEL INFORMATION

On December 14, 1998, the left seat pilot was issued a private pilot certificate. He held single and multi-engine land ratings in addition to an instrument-airplane rating. According to a Client Information Sheet, provided by Flight Safety International Inc., Flushing, New York, on December 13, 1999, he enrolled in the "MU-2 Pilot-Initial" course in Houston, Texas. The sheet indicated that he had accumulated a total of 950 flight hours. Additional documents provided by Flight Safety International revealed that during the MU-2 course, the pilot accumulated a total of 20.0 hours in an MU-2 flight simulator; however, he did not complete the MU-2 Pilot-Initial course. He was issued his most recent FAA third class medical certificate, with no limitations or waivers, on September 11, 1998.

On April 6, 1980, the right seat pilot was issued a commercial pilot certificate. He held single and multi-engine land ratings in addition to an instrument-airplane rating. According to a Client Information Sheet, provided by Flight Safety International Inc., Flushing, New York, on December 13, 1999, the pilot enrolled in the "MU-2 Pilot-Initial" course in Houston, Texas. The sheet indicated that he had accumulated a total of 2,000 flight hours. On December 22, 1999, he successfully completed the MU-2 Pilot-Initial Course. Additional documents from Flight Safety International revealed that during the MU-2 course, the pilot accumulated a total of 20.0 hours in an MU-2 flight simulator and 16.9 hours in the accident airplane. He was issued his most recent FAA second class medical certificate on June 22, 1999. The medical certificate stipulated that the pilot wear lenses that correct for distant vision and possess glasses that correct for near vision.

On January 5th and 6th, 2000, a flight instructor flew 4.5 hours with the private pilot and 3.7 hours with the commercial pilot in the accident airplane. The purpose of the flights was for the pilots to "build time to meet insurance requirements." Both pilots performed flight maneuvers including "high speed and slow flight, turns (high and low speed), and stalls in all configurations with recoveries." The instructor pilot "pulled one engine back to idle," and he reported that the commercial pilot "displayed satisfactory performance in recognizing and simulating shutdown and controlling the aircraft." On January 7, 2000, the airplane was flown by the instructor and the private pilot to Intercontinental Jet Corporation (IJC), a maintenance facility located in Tulsa, Oklahoma, where it underwent maintenance.

AIRCRAFT INFORMATION

The 1978 model Mitsubishi MU-2B-26A (serial number 386SA) airplane was powered by two 665-horsepower Honeywell TPE331-5-252M turboprop engines (serial numbers P-30003C and P-30012C). The airplane was equipped with two 4-bladed, Hartzell HC-B4TN-5GL constant speed, manual feathering propellers. The airplane was outfitted with flight controls for the left and right seats.

Prior to 1999, the airplane was operated outside of the United States for an undetermined time period. In April of 1999, the airplane was purchased by Turbine Aircraft Services Inc., of Addison, Texas, and imported to the United States.

On April 15, 1999, maintenance commenced at IJC. The airframe underwent 100-hour, 500-hour, 1,000-hour, 1,500-hour and 2,000-hour inspections. At the time of the inspections, the airframe had accumulated a total of 3,717.7 hours. The left engine underwent a 100-hour inspection and had accumulated a total of 3,717.7 hours and 3,534 cycles. The right engine underwent a 100-hour inspection and had accumulated a total of 3,717.7 hours and 3,529 cycles. According to a logbook entry, the right engine was disassembled to "investigate low power." The diffuser assembly was overhauled, and the compressor housing, the support assembly, the seal assembly, and the plug seal were replaced. The engine's airworthiness directives and service bulletin compliance record was also updated. Following reassembly of the right engine, the airplane was test flown and found to meet the manufacturer's specifications. During the test flight, a negative torque sensing (NTS) system check was performed and no discrepancies were noted. The left and right propeller assemblies underwent 100-hour inspections, and had accumulated a total of 121.7 hours since overhaul. On August 19, 1999, the maintenance was completed.

On August 20, 1999, the FAA issued the airplane a standard airworthiness certificate.

On November 5, 1999, the airplane underwent maintenance at IJC. According to a work order, the maintenance consisted of correction of "misc. airframe discrepancies, LH engine misc. discrepancies, RH engine misc. discrepancies, and misc. nav/comm. Pulse or radar discrepancies." According to a discrepancy report sheet a 6-8% torque split was reported and the following action was recorded: "checked torque per DSC, lower R/H torque 6%, set L/H torque downlock."

On November 16, 1999, the airplane underwent maintenance at IJC. According to a work order, the maintenance consisted of correction of "misc. nav/comm., pulse or radar discrepancies." Additionally, an oil and filter analysis was performed on the left and right engines by Skywatch Inc., of Norcross, Georgia. The results were "normal" for both engines.

On December 18, 1999, the airplane underwent maintenance at IJC. According to a work order, the maintenance consisted of "misc avionics install."

On January 3, 2000, the airplane was registered to BTC Saratoga, Inc.

On January 10, 2000, the airplane underwent maintenance at IJC. According to work orders, the maintenance consisted of correction of "misc. airframe discrepancies and misc. nav/comm., pulse or radar discrepancies."

On January 20, 2000, the airplane underwent its most recent maintenance at IJC. The maintenance consisted of installing new pitch, roll, and yaw servos, and correcting "nav/com, pulse or radar discrepancies." A pilot from IJC flew the airplane to test the avionics system and the autopilot. He reported that the flight was "normal and all systems performed properly."

On January 21, 2000, a pilot from IJC flew the airplane from Tulsa to San Antonio, at the request of the owner. He reported that the 1.9-hour flight was normal and all systems performed properly. At that time, the airframe and engines had accumulated approximately 3,767.2 hours.

According to the airplane's flight manual, with one engine operating and 20 degrees of flaps extended, the minimum control speed (Vmc) is 93 KCAS (knots calibrated airspeed).

The flight manual's emergency procedure for an engine failure during takeoff prior to liftoff is:

1. Power Levers- Ground Idle

2. Brakes- As Necessary

3. Reverse Thrust- As Necessary

The flight manual's emergency procedure for an engine failure during the takeoff climb (gear down or in transit to up) is:

1. Landing Gear- Down

2. Operating Engine- Power as Required

3. Flaps- Leave in Takeoff Position

4. Land straight ahead using airspeed appropriate for the airplane weight,

but not less than 100 KCAS.

A warning following this procedure in the flight manual states: "If flaps 20 degrees takeoff is selected and engine failure occurs after liftoff, continued climb performance is not assured unless the landing gear has completely retracted, the gear doors are closed, and the flaps are at 5 degrees or less."

At the request of the NTSB Investigator-In-Charge (IIC), Mitsubishi calculated the airplane's takeoff weight and center of gravity as 9,972.8 pounds and 157.76 inches, respectively. The airplane's maximum takeoff weight was 10,470 pounds and the center of gravity limits were 153.7 to 161.6 inches. The airplane's total takeoff distance over a 50-foot obstacle, with the flaps extended 20 degrees, at the gross weight calculated, under the reported weather conditions, was determined to be 3,610 feet.

METEOROLOGICAL INFORMATION

At 1438, the weather observation facility at the San Antonio International Airport reported the following weather conditions: overcast skies at 25,000 feet, visibility 10 miles, wind from 220 degrees at 8 knots, temperature 69 degrees Fahrenheit, dew point 57 degrees Fahrenheit, and an altimeter setting of 29.83 inches of Mercury.

WRECKAGE AND IMPACT INFORMATION

The airplane came to rest in a vacant, dirt lot in a residential area approximately 1 mile north of the airport. A global positioning system (GPS) receiver recorded the location at north 029 degrees 33.135 minutes latitude and west 098 degrees 28.983 minutes longitude. The energy path, from the initial impact point to the main wreckage, encompassed an area 175 feet in length and 150 feet in width. The linear energy path was oriented on a measured magnetic heading of 030 degrees, and the fuselage came to rest on a measured magnetic heading of 220 degrees. The initial impact point was a crater consistent with the dimensions of a wing-tip fuel tank. The pitot tube, which was mounted on the right side of the airplane's nose, and a counterweight from the right propeller were located adjacent to the initial impact point. A propeller blade from the left propeller assembly was located 26 feet from the initial impact point. A crater, consistent with the dimensions of an engine, and the strake from the left wing-tip fuel tank were located aft of the left propeller blade. The left propeller hub assembly (three blades remained attached) was located 63 feet from the initial impact point. The right wing-tip fuel tank was located 70 feet beyond the initial impact point, and the right engine and propeller hub assembly (two blades remained attached) were located at 123 feet. The left engine was located 136 feet beyond the initial impact point, and the main wreckage came to rest at 155 feet. The two remaining propeller blades from the right engine were located at 10 and 20 feet north of the main wreckage. The final piece of wreckage located along the linear path was the left wing-tip fuel tank, located 175 feet from the initial impact point.

The main wreckage consisted of the cockpit, fuselage, both wings, and the tail section. The fuselage came to rest on its left side. The main wreckage was heavily damaged by fire. The wing center section was twisted, separated from the fuselage, and came to rest inverted across the cockpit. Both outboard wing sections were separated from the wing structure. The left horizontal stabilizer was folded beneath the tail section, and the right horizontal stabilizer was oriented in a vertical position. No cockpit instrument readings or switch positions could be verified as a result of the fire damage.

The flaps were found extended 20 degrees (normal takeoff position). The landing gear was in the retracted position. The power lever for the right engine was at the flight idle position, and the condition lever for the right engine was at the takeoff/land position. The power lever for the left engine was in the full forward position, and the condition lever was at the takeoff/land position. Additionally, the left and right engine firewall fue

NTSB Probable Cause

the pilot's failure to maintain the minimum controllable airspeed following a loss of engine power during the initial takeoff climb. Contributing factors to the accident were both pilot's lack of total experience in the make and model of the accident airplane and the loss of right engine power for an undetermined reason.